Fixes:
* scsi: Fix a bug that caused the device capacity to be set
to an undefined value for some large SCSI devices when
READ CAPACITY (16) was used
* ahci: Fix VPD page reporting so that it does not return
undefined values
* ahci: Set the write bit to true when sending a DATA SET
MANAGEMENT (trim) command to a device. The command would
otherwise fail and time out on some devices.
Improvements:
* scsi: Extend the READ CAPACITY (16) support to also
include logical block provisioning information
* scsi: Prefer READ CAPACITY (16) over READ CAPACITY (10)
on devices that are expected to support this command
* scsi, ahci: Enable trim on SCSI and SATA devices that
are expected to support trim and which correctly report
trim support
* ahci: Redo the implementation of the SCSI UNMAP command
* scsi: Redo UNMAP-related code
* scsi: Add support for UNMAP via WRITE SAME (10) and
WRITE SAME (16) commands
* When copying trim ranges between different data types,
make sure that the values don't change (detect overflows)
* Report the number of trimmed blocks even if the trim
operation fails
Change-Id: Ie5fc993bbbc19546b4308138ba10184bf7b9986a
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4157
Tested-by: Commit checker robot <no-reply+buildbot@haiku-os.org>
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Fixes:
* Use uint64 instead of off_t when handling offset and size
of the trimmed range in the fs_trim_data structure
* BlockAllocator::Trim: Correct the size of a buffer
* ram_disk, mmc: Do not trim past device capacity
Improvements:
* BlockAllocator::Trim: Because the received offset and size
are ignored by BFS (the functionality is not implemented yet),
return B_UNSUPPORTED if the range does not cover the whole
partition
* ram_disk, mmc: More accurate calculation of the number
of trimmed bytes
* devfs: Add a uint64 version of translate_partition_access()
Change-Id: I24f4c08674f123ad33a5fef6e28996a4ada6ff0d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4155
Tested-by: Commit checker robot <no-reply+buildbot@haiku-os.org>
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
* Makes the case where the loader and the install differ by
release type, so that the icons are rendered in the same
position
Change-Id: I01e48109ce127b202ce5e05544aa2d5a495ed53e
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4162
Tested-by: Commit checker robot <no-reply+buildbot@haiku-os.org>
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Reviewed-by: Alex von Gluck IV <kallisti5@unixzen.com>
This also keeps the functionality of hrev53848, which simplifies the
list of disks searched for bootable partitions; however, it maintains
the previous behaviour of platform_get_boot_partitions that continues
to iterate over a list of possible boot partitions, which should
allow finding a bootable BFS partition better in more circumstances.
Particularly, there are numerous reports of the UEFI loader entering
the boot menu despite it finding a bootable partition, which this
should address.
EFI's device_contains_partition is also structured such that it
compares the disk GPT table of the partition the loader is
querying of the EFI disk's GPT table, in the case that there are
multiple disks, as the most reliable method of comparison, with
a generic fallback for non-GPT disks, which will be less reliable.
This reverts commit 0d932a49ad.
Change-Id: I5fac8608035d56b8bb4dc6c3d495ec6db42fa9b7
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4149
Reviewed-by: Alex von Gluck IV <kallisti5@unixzen.com>
* This will break previus ways to store settings (as it only stored a struct)
* Now we use BMessage to save data.
* Added some stuff to SettingsMessage.
* Fix a bug in BluetoothSettingsView::_GetClassForMenu() and SettingsMessage::SetValue
Change-Id: I6a0fa1564e78460258f480947592eb4007985007
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3887
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Tested-by: Commit checker robot <no-reply+buildbot@haiku-os.org>
the AC flag in eflags/rflags, pushed in the iframe by the CPU, is kept intact after handling the exception, since the fault handler is run with the faulted iframe and does a simple jump. The AC flag would otherwise be set until the syscall returns to userland.
Change-Id: I24f763032ab98029dd162fb411e1541586451606
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4040
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Tested-by: Commit checker robot <no-reply+buildbot@haiku-os.org>
It is not present in BeOS R5 and it just call unload_driver_settings.
Replace delete_driver_settings usages with unload_driver_settings.
Keep the symbol on x86 for binary compatibility.
Change-Id: I1382710e3a4cb5c65d1249ea0e5880891e6800e4
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3485
Reviewed-by: Jérôme Duval <jerome.duval@gmail.com>
It cause adding new entry to executable init array for each translation unit.
Change-Id: I1e2d7946da03c001de7721948bc9af8188e8b317
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3981
Reviewed-by: X512 <danger_mail@list.ru>
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
this adds kernel & libroot stack protector hooks. it uses /dev/random in userspace.
A configure option --enable-stack-protector is added to activate -fstack-protector
on selected system components (ATM apps, kits, servers).
Change-Id: If3a2920ba9aa0a85eaff4ba6778947f8c76ade31
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3895
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
* Thanks to kottan I notices something was of..
* Added uInt16 and uInt64, I was missing UInt16.
Change-Id: Id136dbb5a81392a7a694ac1fbbd9aefbd7f77af3
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3888
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
* Move SettingsMessage
* Remove SettingsMessage from MediaPlayer and WebPositive
* Use the central SettingsMessage in MediaPlayer and WebPositive (Later Bluetooth)
* Fix a Jam file.
Change-Id: I3bb82a40082c5ece5c2aea2468a77bcd9f15ce77
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3856
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
* Inactiveate button and things that don't do anything.
* Those button and controlles that hade any actions in the Bluetooth Pref now saves in settings.
* Fix some windows/views.
* Fix Copyright in last Bluetooth commit.
* Last commit before we move saving settings with BMessage.
* Changed PoupMenu to BOptionPopUp
Change-Id: I32b85f1985b558d24b294a184665e08e6ce18a7d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3829
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
This is not my code but from ticket #9265
* Made a picture of how it looks, old left andnew right. https://imagebin.ca/v/5wIe6TIMzw4C
* Think we have a bug somewhere and don't store the name of the Bluetooth device (shown i the image).
* I have made som small changes but other than that it's the same code as in the ticket
* Ran the src/tools/checkstyle/checkstyle.py to get som style stuff, probably missed some anyway.
Change-Id: Ifeb75c8ad890f541e100cdcf78b394675a48ada9
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3825
Reviewed-by: Fredrik Modéen <fredrik@modeen.se>
Various projects, both commercial and OSS, began to use inclusive
terminology. There is no reason to not do it.
In Haiku, bootloader uses Blacklist, which is recommended to replace
with Denylist or Blocklist. I think Blocklist is appropriate here,
since it's a list used to block offending driver at boot.
Some strings remain unchanged for compatibility with previous naming,
but this change prepares for later removal of these (once everyone has
updated their kernel and bootloader).
Change-Id: Id9105ff5e9fcb866000355089b5ef97bf63ee854
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3145
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
a protection_max attribute is added in VMArea.
a read-only opened file already can't be mapped shared read-write at the moment,
but can later be changed to read-write with mprotect() or set_area_protection().
When creating the VMArea, the actual maximum protection is stored in the area,
so that it can be checked when needed.
this fixes a VM TODO.
Change-Id: I33b144c192034eeb059f1dede5dbef5af947280d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3804
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
The standardized version of readv() and writev() take an int as the third
parameter. Arguably a size_t makes more sense, but the standardization bodies
decided otherwise.
The non-standard functions of readv_pos() and writev_pos() have been updated
for consistency. The corresponding _kern_readv() and _kern_writev() internal
functions continue to take the size_t parameter.
The ABI will not change, even though on 64 bit machines the size of the count
parameter will change from 8 to 4 bytes.
The actual use will be slightly different. Like with the size_t argument type,
it will not be possible to give a count lower than 0. If the value is less than
0, then the B_BAD_VALUE/EINVAL error will be set.
Change-Id: I949c8ed67dbc0b4e209768cbdee554c929fc242e
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3770
Reviewed-by: Jérôme Duval <jerome.duval@gmail.com>
Do the final installation operations for all the packages in the
/system/packages directory when the OS is booted for the first time.
This will run their post-install scripts, create users, groups and generate
settings files (marked with a package version attribute). Previously we just
ran all the shell scripts found in the /system/boot/post-install directory
(don't do that as much now).
Fixes bug #14382
This patch has simpler code flow in CommitTransactionHandler::_ApplyChanges
Tested on 32 and 64 bit systems. Once it's official, need to remove the
open_ssh redundant post-install script that creates users etc. from HaikuPorts.
Now we can notice bugs like package version attributes on settings files aren't
fully working. :-)
Didn't remove special case for add_catalog_entry_attributes.sh since it
still does stuff that the build system doesn't do. Might be able to add
that script as part of the Haiku.hpkg. See change 3751 for removing it,
https://review.haiku-os.org/c/haiku/+/3751
Change-Id: I3807b78042fdb70e5a79eca2e2a45816ece0236f
Reviewed-on: https://review.haiku-os.org/c/haiku/+/2342
Reviewed-by: Alexander G. M. Smith <agmsmith@ncf.ca>
Reviewed-by: Niels Sascha Reedijk <niels.reedijk@gmail.com>
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Previously, BUrlRequest returns data received via a callback that can't
return any value. This approach have several issues:
- It's not possible to signify failures to the request.
- Users have to implement custom listeners just to handle the common
case of outputting to a buffer/file/etc.
- The received data has to be serialized into BMessage when
BUrlProtocolDispatchingListener is employed. This can cause a
noticible slowdown in real-world scenarios as evident by #10748.
With this change, BUrlRequest will output directly into a BDataIO, which
exposes a richer API for request handlers to work with (for example a
BitTorrent client can request a BPositionIO for non-linear data
delivery), as well as simplifying common cases for users.
The adaptation only requires one additional API:
BHttpRequest::SetStopOnError(). This API simply instructs the HTTP
request handler to cancel the request if an HTTP error is occurred.
Change-Id: I4160884d77bff0e7678e0a623e2587987704443a
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3084
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
The switch to make BUrlResult serializable was debuted in
f9e1854f19 with the rationale is that
BHttpRequest auto-redirection might cause the headers to become
obsolete by the time a client process the BMessage received from
BUrlProtocolDispatchingListener.
With the change to BHttpRequest to not notify listeners when
auto-redirection is enabled, this is no longer the case and the
serialization code can go away now. This simplifies BUrlResult and its
subclasses, and gain us some performance for clients using
BUrlProtocolDispatchingListener as the result object no longer has to be
serialized.
This also change the ABI of BUrlProtocolListener::HeadersReceived to no
longer passing a BUrlResult.
Additionally, BUrlResult and BHttpResult now express the size of the content
as an off_t, thus allowing results larger than 4 GB.
Change-Id: I9dd29a8b26fdd9aa8e5bbad8d1728084f136312d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3082
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Further removal of the use of custom list class;
this time with the package lists.
Relates To #15534
Change-Id: I1f01ed9d5ddbd7754097ce0adbf505d6ba17fd2f
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3732
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
This change only applies in libnetservices.a. The implementation in
libbnetapi.so will use the original definitions.
Change-Id: I0aaa5a40af5fbcafaf233c32206cb4af862f8141
Reviewed-on: https://review.haiku-os.org/c/haiku/+/2465
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
The BGeolocation class uses the network interface in libnetservices.a, so it
is moved here for now.
This will break any out of tree projects that depend on it, but it is a source
incompatible change only.
Change-Id: I6f5b1332eb87ad37dd33fbe09fdb11b16f7f26e4
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3670
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
In order to prevent classes between libnetapi.so with the legacy API and
applications using the libnetservices.a library, the latter will have the
classes in a distinct namespace.
In the implementation, both libbnetapi.so and libnetservices.a will use the
same header and source files. If LIBNETAPI_DEPRECATED is defined during build,
the headers and source will have binary compatible behavior. Otherwise, the
classes and other objects will be put in the HaikuExt namespace.
In order to build the libbnetapi.so and libnetservices.a with the proper
build configuration, there is a stub `src/kits/net/libnetapi_deprecated` folder
that applies the special configuration to the source files.
Currently HaikuDepot, Webpositive, libshared.a and the http_streamer add on
use the compatible API in libbnetapi.so.
Change-Id: Ic73e9f271ef75749adda46f6f72e9a0b2851b461
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3667
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
These classes have been moved to the public API too soon, and they need some
more time to mature before they can be declared stable.
Change-Id: I9c52a8e6cc103922abde7a6b911fe0c3e6bf5700
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3665
Reviewed-by: Adrien Destugues <pulkomandy@gmail.com>
Store the bus cookie in the mmc_disk driver and pass it to the bus
manager when executing commands. This avoids calling into the device
manager at each read and write operation. The code to get the cookie
from mmc_disk isn't so nice since it needs to access the grandparent
device (the mmc bus root), it would be simpler if this cookie would be
available directly from mmc bus devices.
We can get card removal and card insertion interrupt at the same time
due to insufficient hardware debouncing (the SDHCI spec says we
shouldn't, but it happens on Ricoh controllers. Can't blame them, they
don't advertise themselves as compliant with the spec). So, check the
card status from the interrupt handler and ignore the incorrect
interrupts.
Fix unreliable card initialization: power must be turned on before
starting up the SD clock. Remove a now unneeded delay that was added in
an attempt to avoid initial instability.
Change-Id: Ibd8d051da1a1d859f3924ee535f4a05d9b6398d4
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3639
Reviewed-by: Jérôme Duval <jerome.duval@gmail.com>
Pascal Abresch
David Sebek